Back to Blog
![]() If your appliance has one, ensure the insulation blanket isn't preventing the dishwasher from fitting correctly in the cabinet opening.Īlign the front of the dishwasher door panel with the front of the cabinet doors and check that the leveling legs are firmly against the floor. Route the power cord, water supply and drain into the cabinet opening before sliding the dishwasher into its final position. Level your dishwasher by following these tips: To operate properly, your dishwasher must be supported by the leveling legs and rear wheels which help it sit flat on the floor. The dishwasher must fit well in the cabinet-if the tub opening is not square, the door will not seal properly. Inspect your appliance for signs of misalignment. You can try to fix this problem by leveling your dishwasher. If your dishwasher wasn't leveled correctly during installation, this can lead to the door not closing or latching properly. Springs should be in the same notches on the left and right sides. ![]() If the door falls open, increase the spring tension by moving the spring end toward the back of the dishwasher. If the door closes too quickly, decrease the spring tension by moving the spring end toward the front of the dishwasher. Using a Phillips-head screwdriver, turn screws clockwise to increase tension or counterclockwise to decrease door tension. Locate the door spring adjustment screws at the base of the dishwasher door. Open and close the door to check the spring tension. Note that exact instructions may vary if you have another brand dishwasher: You can try fixing this problem by adjusting the tension on the springs for a tighter fitting door.įollow these steps to check the door spring tension of your Whirlpool ® dishwasher according to its type. This means that the tension on the door springs isn’t strong enough to keep the door closed. Flip the dishwasher’s circuit breaker back on, and open the water supply valve.If the dishwasher door won’t close or latch, it might be because the door spring tension is improperly set.Finally, now that the dishwasher has been fully reassembled, you can now restore power and water to the dishwasher.Then, reinstall the cover panel, also making sure that it is fully screwed in.Next, reinstall the brackets that hold the dishwasher in place, making sure the screws are fully tightened.Start by pushing the dishwasher back into its original position, then reconnect the power wires to the junction box and reinstall the junction box cover.Once you’ve reinstalled the new springs correctly, it’s time to put everything back together again. To install the new springs, first attach one end to the dishwasher door hinge, then use a pair of pliers to pull the other end of the spring onto the bracket.If that’s the case, you’ll have to have the brackets replaced instead. It’s also possible that the brackets that the springs attach to have broken instead of the springs themselves. It’s important to note that not all dishwasher door springs are universal, so you need to make sure that any replacement springs you use are actually compatible with the make and model of the dishwasher you have. If the spring has broken or has become too stretched out and no longer has any tension, you’ll have to replace the spring.If you’re lucky, it may only be that one of the springs has become detached from either the door hinge or the door spring bracket, in which case you can fix the issue by simply reattaching the spring to the bracket.As we’ve said, the door springs are located on either side of the dishwasher, close to the bottom and towards the front of the unit.Įxamine the springs and see what the damage is. Check/Remove the Springs and Replace Them If NecessaryĪt this point, you should now have your dishwasher in a position where you can inspect the door springs. The brackets will likely be held in place by screws, so just remove these screws and you should be able to move the dishwasher out of its cubby. Odds are, your dishwasher also has a couple of brackets to keep it in place inside its cubby these will also have to be removed. This is why it’s important to ensure that your dishwasher is not receiving power otherwise, you risk electrocuting yourself with this step. If these wires don’t have enough slack, however, you’ll have to disconnect them from the junction box before pulling the dishwasher out from its cubby.
0 Comments
Read More
Leave a Reply. |